Ford Racing Performace Parts - 2005-2010 Mustang GT - X-PIPE
T-409 stainless steel X-pipe
Converts your factory H-pipe to a more efficient X-pipe
Requires cutting of factory exhaust for installation
Clamp on installation - does not require welding!
Ford Racing Performance 1979-1993 Mustang LX/GT 5.0 - Shorty Headers
Also fits early “Fox” vehicles with modifications
2 Jet-Hot® Limited Warranty
3 Production and all GT-40 heads
5 Finally a header that fits the new angled spark plug 5.0L GT-40 “P” cylinder head. Fits 1986-93 Mustangs with stock or aftermarket H-pipe. Also fits 1979-85 Mustangs and other Fox chassis with minor modification
FORD RACING PERFORMANCE PART 1996-2009 MUSTANG A/C ELIMINATOR KIT
Fits 1996-2009 Mustang with 4.6L engine SOHC/DOHC
Cast aluminum idler pulley bracket replaces the air conditioning compressor
Removes weight from the front of car for better weight transfer when racing
Bolts included
Uses stock belt
Ford Racing Performance Parts - 04-08 Ford F-150 2WD LOWERING KIT
Fits 2004-2008 F-150 2WD Standard and Extended Cab with V6 or V8 (will not fit Heritage, SuperCrew or 4WD.
Lowers approximately. 2" front and 5" rear
Improves appearance and lowers vehicle roll center for better handling with very acceptable ride characteristics
Includes front coil springs, rear flip kit, specially tuned high-pressure gas rear shocks, bump stops and hardware
Ford Racing Performance Parts - 04-10 Ford F-150 REAR LOWERING KIT
Fits 2004-2010 F-150
Lowers rear of vehicle
Lowers 2.0" on 2WD or 1.5" on 4WD
Contains all installation hardware
Ford Racing Performance Parts - 07-08 Mustang Shelby GT500 Ford Racing Shorty Headers
2007-08 SVT MUSTANG SHORTY HEADERS
•Fits 2007-08 SVT Mustang
•409 stainless steel tubes, 1 7/8" diameter
•Machined flange
•9 lbs lighter than cast iron manifolds
•Bolts to stock catted X pipe or JBA Off-Road X pipe
•Includes gaskets, bolts and studs
Ford Racing Performance Parts - 07-08 Mustang Shelby GT500 Ford Racing Shorty Headers (Ceramic Coated)
2007-08 SVT MUSTANG SHORTY HEADERS
•Fits 2007-08 SVT Mustang
•409 stainless steel tubes, 1 7/8" diameter
•Machined flange
•9 lbs lighter than cast iron manifolds
•Bolts to stock catted X pipe or JBA Off-Road X pipe
•Includes gaskets, bolts and studs
Ford Racing Performance Parts - 07-09 Mustang Shelby GT500 62.5MM Cobra Jet Billet Aluminum Throttle Body
COBRA JET BILLET ALUMINUM THROTTLE BODY M-9926-CJ* * Service replacement for the 2008 Mustang FR500CJ race car * Fits in factory location on 2007-2009 SVT Mustang * Twin 63.5mm bore (stock SVT Mustang is twin 60mm) * Tested to over 800 hp in 2007-2009 SVT Mustang applications * Precision machined from billet aluminum to ensure consistency * Polished finish with machined Ford Racing logo * Tested to Ford original equipment specifications for cold and hot weather * Fully assembled, complete with throttle position sensor and actuator motor, ready to bolt on! * Uses OE gears to prevent gear bind and wear common with other aftermarket throttle bodies * Does not include calibration, calibration may be required in some applications
Ford Racing Performance Parts - 07-09 Mustang Shelby GT500 Ford Racing GT500 113MM Cold Air Intake and Pro-Cal Tuner Package
M-9603-SVT07
- Fits 2007-09 SVT Mustang
- Kit includes 113 mm Mass Air Meter
- Mounts in the stock location
- Premium fuel only
- 40 hp increase over stock using correction factor SAE J1349
- Due to multiple calibrations, online registration is required to receive Pro-Cal 2 tool after purchase.
- E.O. #D-308-12
- Good for those looking to mod their GT500 but still be very warranty friendly
M9603SVT07
Ford Racing Performance Parts - 07-09 Mustang Shelby GT500 Ford Racing GT500 113MM Cold Air Intake Only
Finally, FRPP offers their intake without a pro-cal, so you can choose to get your own tuning.
Ford Racing Performance Parts - 07-09 Mustang Shelby GT500 FR500S "KR" Mufflers
# Fits 2005-2009 Mustang GT and 2007-2009 Mustang SVT. For 2010 Mustang GT / SVT see M-5230-SA # Homologated for use on the Mustang FR500S # Body of mufflers embossed with Ford Racing logo # Aluminized 409 stainless steel corrosion-resistant body with polished 304 stainless 3.5" diameter tips # Throatier exhaust note # 50 state drive-by noise legal
M9603CJ123MM - 07-09 Mustang Shelby GT500 FRPP 123MM Cobra Jet CJ Cold Air Kit
2008 COBRA JET COLD AIR KIT
M-9603-CJ*
* Fits 2007-2009 SVT Mustang
* Original equipment on 2008 FR500CJ Cobra Jet
* Kit includes:
o 123 mm Cobra Jet Mass Air Sensor Housing M-9600-CJ
o 2007-2010 SVT Mustang Mass Air Sensor element and zip tube
o Plastic bucket and all fasteners
o Disposable air filter element M-9601-D
* A performance calibration is necessary to prevent engine damage. Calibration not included!
Ford Racing Performance Parts - 07-09 Mustang Shelby GT500 FRPP 123MM Cobra Jet CJ MAF Housing Only
2008 COBRA JET COLD AIR KIT
M-9600-CJ*
* 123 mm Mass Air Flow Sensor Housing
* Add to your underhood "bling" factor with this massive mass air housing that looks as good as it performs!
* Cobra Jet Mass air meter housing - recommended for highly modified 2007-2009 Mustang SVT's
* Proven to support over 800 hp in 2007-2009 Mustang SVT applications
* Eliminates production resonator
* Fits production air tube
* Precision CNC'd billet aluminum
* Polished finish
* This kit includes the housing and mounting tab
* Perfect upgrade to existing Ford Racing Mustang SVT power upgrade, cold air, and supercharger kits!
* Does not include calibration, CALIBRATON REQUIRED, sold for tuner use
Ford Racing Performance Parts - 07-10 Mustang Shelby GT500 65MM Cobra Jet Billet Aluminum Throttle Body
65MM COBRA JET BILLET ALUMINUM THROTTLE BODY M-9926-CJ65* * Fits in factory location on 2007-2010 SVT Mustang * Twin 65mm bore (stock SVT Mustang is twin 60mm bore) * Precision machined from billet aluminum to ensure consistency * Polished finish with machined Ford Racing logo * Tested to Ford original equipment specifications for cold and hot weather * Fully assembled, complete with throttle position sensor and actuator motor, ready to bolt on! * Uses OE gears to prevent gear bind and wear common with other aftermarket throttle bodies * Does not include calibration, calibration may be required in some applications
Ford Racing Performance Parts - 07-11 Mustang Shelby GT500 2008 Ford Racing OEM GT500 Balancer - improved design
The 2008 GT500 balancer is of an improved design, nearly half the weight of the 07 balancer.
The 2007 GT500 uses a very heavy 26lb balancer, which results in a lot of stress on the crank snout. It is recommended to upgrade to the 2008 part when installing an aftermarket supercharger or raising boost on the stock supercharger.
Includes:
•2008 GT500 OEM/Ford Racing balancer
•Longer M12 crank bolt for installation
•Three M10 bolts to remove stock 07 balaner with standard removal tool
