Ford Racing Performace Parts - 1999-2004 Mustang - 9MM Spark plug wire set (Red)
Wire-wound custom ignition wire sets feature low resistance for minimum spark loss. Silicone insulation and boots withstand high temperatures and voltage loss for minimum cross-fire and are highly resistant to fuels, oils and solvents. Long-life, tough stainless steel terminals for “post” type distributor caps. Includes coil wire for socket-type coil and “Ford Racing” identification. Cylinder number appears on each wire.
NEW AND IMPROVED Spark plug wires feature high quality 9mm wire available in 4 colors: blue, black, yellow and red.
Ford Racing Performace Parts - 1999-2004 Mustang - 9MM Spark plug wire set (Red)
4.6L 4V Mustang Red 45° Long Boot
Wire-wound custom ignition wire sets feature low resistance for minimum spark loss. Silicone insulation and boots withstand high temperatures and voltage loss for minimum cross-fire and are highly resistant to fuels, oils and solvents. Long-life, tough stainless steel terminals for “post” type distributor caps. Includes coil wire for socket-type coil and “Ford Racing” identification. Cylinder number appears on each wire.
Ford Racing Performace Parts - 1999-2004 Mustang - Clutch Disc
NOTES: 1 Clutches have NO warranty! 2 All clutch discs have 1.0625"-10 spline hub. 3 Fits all 1986-01 Mustang GT, 1993-98 Cobra with T-5 or T45 Transmissions. 2001-04 Mustang GT with 3650 transmission and 1999-03 Cobra uses an 11" clutch. OK to mix and match Ford Racing clutch discs and pressure plates but do NOT install a FRPP pressure plate with a stock disc or vice-versa as disengagement problems may occur. Installation of 10.5" clutch assemblies on 1979-85 vehicles equipped with 10" clutch requires new flywheel (see page 116). Metric fasteners and dowel pins must be used with 10.5" clutches. 4 Requires metric pressure plate bolts N602549-S51M and alignment dowel pins D1FZ-6397
Ford Racing Performace Parts - 1999-2004 Mustang - Clutch Disc
HD disc with carbon/copper lining on flywheel side and carbon lining on pressure plate side.
Ford Racing Performace Parts - 1999-2004 Mustang - Clutch Disc
HD disc with carbon/copper lining on flywheel side and carbon lining on pressure plate side.
Ford Racing Performace Parts - 1999-2004 Mustang - Clutch Kit
NOTES: 1 Clutches have NO warranty! 2 All clutch discs have 1.0625"-10 spline hub. 3 Fits all 1986-01 Mustang GT, 1993-98 Cobra with T-5 or T45 Transmissions. 2001-04 Mustang GT with 3650 transmission and 1999-03 Cobra uses an 11" clutch. OK to mix and match Ford Racing clutch discs and pressure plates but do NOT install a FRPP pressure plate with a stock disc or vice-versa as disengagement problems may occur. Installation of 10.5" clutch assemblies on 1979-85 vehicles equipped with 10" clutch requires new flywheel (see page 116). Metric fasteners and dowel pins must be used with 10.5" clutches. 4 Requires metric pressure plate bolts N602549-S51M and alignment dowel pins D1FZ-6397-
Ford Racing Performace Parts - 1999-2004 Mustang - Performance Flywheel
NOTES: 1 Diaphragm clutch uses metric bolts and dowel pins. Requires metric pressure plate bolts N602549-S51M and alignment dowel pins D1FZ-6397-B. Ford Racing kit M-6397-A302. 2 4.6L engines may have 6 or 8 bolts to attach to the crankshaft. Check the engine code before ordering. Romeo built engines have 6 bolts and Windsor built engines have 8 bolts. All Cobra engines have 8 bolts. The 8th character in the VIN is (X) for Windsor engine plant or (W) for Romeo engine plant. 3 Has bolt-on counterweight 4" long for A302, 7.2" long for C302.
Ford Racing Performace Parts - 1999-2004 Mustang - Pressure Plate
HD “King Cobra” diaphragm type. Same capacity a M-7563-A302N above but stronger cover and revised internal geometry reduce clutch pedal effort by 10%. Nodular iron plate.
Ford Racing Performace Parts - 1999-2004 Mustang - Roller pilot bearing 4.6 & 5.4 modular motors
Production roller pilot bearing fits 4.6L/5.4L modular engines
NOTE: Pre-greased – do not add extra grease. Clutch and bearing damage may occur
Ford Racing Performace Parts - 1999-2004 Mustang Cobra- IRS Hub
5 x 4.5" bolt circle, 2.775" wheel pilot hub for popular Mustang size wheels
Should be used with IRS knuckle M-5970-A
Original equipment on 1999-2004 Mustang Cobra
Ford Racing Performace Parts - 2001-2004 Mustang - 4.6L Performance Improvement (PI) Intake Manifold
Current production plastic intake manifold used on 2001-04 4.6L SOHC 2V Mustang GT
Less expensive alternative to aftermarket performance intake manifolds for PI head swaps
Manifold fits 1999-04 Power Improvement head ports
Great for custom engine builds
Can be used on 1996-98 engines with Performance Improvement (PI) heads
Additional modifications and parts required
FORD RACING PERFORMANCE PART 1996-2009 MUSTANG A/C ELIMINATOR KIT
Fits 1996-2009 Mustang with 4.6L engine SOHC/DOHC
Cast aluminum idler pulley bracket replaces the air conditioning compressor
Removes weight from the front of car for better weight transfer when racing
Bolts included
Uses stock belt
Ford Racing Performance Parts 1994-2004 Mustangs - FRONT LOWER CONTROL ARM KIT
This kit enables owners of 1994-2004 Mustangs to upgrade to the 2003 Cobra Mustang control arms. The kit features 2 front lower control arm assemblies with 50% stiffer front bushings and low-friction ball joints. This control arm has a redesigned stamping to improve the turning circle approximately 10% on 1994-1998 Mustangs
Ford Racing Performance Parts 1999-2004 Mustang GT/Cobra - Clutch Kit
NOTES: 1 Clutches have NO warranty! 2 All clutch discs have 1.0625"-10 spline hub. 3 Fits all 1986-01 Mustang GT, 1993-98 Cobra with T-5 or T45 Transmissions. 2001-04 Mustang GT with 3650 transmission and 1999-03 Cobra uses an 11" clutch. OK to mix and match Ford Racing clutch discs and pressure plates but do NOT install a FRPP pressure plate with a stock disc or vice-versa as disengagement problems may occur. Installation of 10.5" clutch assemblies on 1979-85 vehicles equipped with 10" clutch requires new flywheel (see page 116). Metric fasteners and dowel pins must be used with 10.5" clutches. 4 Requires metric pressure plate bolts N602549-S51M and alignment dowel pins D1FZ-6397-
Ford Racing Performance Parts 1999-2004 Mustang GT/Cobra - Clutch Kit
NOTES: 1 Clutches have NO warranty! 2 All clutch discs have 1.0625"-10 spline hub. 3 Fits all 1986-01 Mustang GT, 1993-98 Cobra with T-5 or T45 Transmissions. 2001-04 Mustang GT with 3650 transmission and 1999-03 Cobra uses an 11" clutch. OK to mix and match Ford Racing clutch discs and pressure plates but do NOT install a FRPP pressure plate with a stock disc or vice-versa as disengagement problems may occur. Installation of 10.5" clutch assemblies on 1979-85 vehicles equipped with 10" clutch requires new flywheel (see page 116). Metric fasteners and dowel pins must be used with 10.5" clutches. 4 Requires metric pressure plate bolts N602549-S51M and alignment dowel pins D1FZ-6397-
