BMR Fabrication 1993-2002 Camaro and Firebird - 2.5"-2.75" brackets and hardware only, no bushings
BMR Fabrication 1993-2002 Camaro and Firebird - 3" - 3.25" brackets and hardware only, no bushings
Have an aftermarket rearend but no way to mount your swaybar? This kit is the solution. Kit contains laser cut, weld-on bushing mounts, polyurethane mounting bushings and endlinks, and all necesarry mounting hardware. Fits all popular Ford 9" and 12 bolt F-Body rear end housings.
BMR Fabrication 1993-2002 Camaro and Firebird - Kit for 19mm swaybars and 2.5" - 2.75" axle tubes
Have an aftermarket rearend but no way to mount your swaybar? This kit is the solution. Kit contains laser cut, weld-on bushing mounts, polyurethane mounting bushings and endlinks, and all necesarry mounting hardware. Fits all popular Ford 9" and 12 bolt F-Body rear end housings.
1993-2002 Camaro and Firebird - Kit for 19mm swaybars and 3" - 3.25" axle tubes
Have an aftermarket rearend but no way to mount your swaybar? This kit is the solution. Kit contains laser cut, weld-on bushing mounts, polyurethane mounting bushings and endlinks, and all necesarry mounting hardware. Fits all popular Ford 9" and 12 bolt F-Body rear end housings.
BMR Fabrication 1993-2002 Camaro and Firebird - Kit for 22mm swaybars and 2.5" - 2.75" axle tubes
Have an aftermarket rearend but no way to mount your swaybar? This kit is the solution. Kit contains laser cut, weld-on bushing mounts, polyurethane mounting bushings and endlinks, and all necesarry mounting hardware. Fits all popular Ford 9" and 12 bolt F-Body rear end housings.
BMR Fabrication 1993-2002 Camaro and Firebird - Kit for 22mm swaybars and 3" - 3.25" axle tubes
Have an aftermarket rearend but no way to mount your swaybar? This kit is the solution. Kit contains laser cut, weld-on bushing mounts, polyurethane mounting bushings and endlinks, and all necesarry mounting hardware. Fits all popular Ford 9" and 12 bolt F-Body rear end housings.
Spohn 1982-2002 Camaro & Firebird Polyurethane Torque Arm Bushing
Polyurethane torque arm bushing for use with the stock torque arm.
Spohn 1993-2002 Camaro & Firebird After Market Rear Sway Bar Installation Kit
So you got yourself a beefy aftermarket rear and when you went to re-install your rear sway bar you realized you had a problem, it doesn't fit! We have the solution.
Spohn 1993-2002 Camaro & Firebird Polyurethane End Link Set - Front Sway Bar
Note: Qty. 1 = 1 Pair
Spohn 1993-2002 Camaro & Firebird Polyurethane End Link Set - Rear Sway Bar
Note: Qty. 1 = 1 Pair
Spohn 1993-2002 Camaro & Firebird Polyurethane Front Lower Ball Joint Boots
Spohn 1993-2002 Camaro & Firebird Polyurethane Front Upper & Lower A-Arm Bushings
Polyurethane front a-arm bushings (without shells).
Note: This kit provides all the bushings for all four a-arms
Spohn 1993-2002 Camaro & Firebird Polyurethane Tie Rod Boots
Polyurethane tie rod boots (2 per package)
Note: Qty. of 2 required to do all (4) tie rod ends
Spohn 1993-2002 Camaro & Firebird Rear LCA Mounting Hardware Kit
Don't use your old rusty mounting bolts when installing aftermarket rear lower control arms (if you managed to get the nuts off without breaking the bolts!).
Spohn 1993-2002 Camaro & Firebird Rear LCA Relocation Brackets - Stock, Strange, Currie Rear Ends
Repositions your instant center by lowering your control arm angle for increased traction and anti-squat. Lowers rear of control arm up to 3". This product is a must for lowered vehicles to correct your suspension geometry. Lowering your vehicle alters the LCA angle putting the rear of the LCA higher than the front of the LCA, this causes massive wheel hop and traction loss.
