MSD Performance Ignition - 86-93 Mustang GT Ford Tach Adapter
If, after installing an MSD Ignition Control, your tachometer, fuel pump relay or electronic fuel injection (in foreign vehicles) doesn’t operate correctly, your application may require a Tach Adapter. This is due to the trigger signal not being strong enough to trigger both the MSD and the factory’s components.There are a few Tach Adapters available and for more information see pages 152 and 153. Each Adapter is simple to wire in and will have your MSD and vehicle firing away in no time! If you are triggering an MSD Blaster, 5, 6, SCI, or 7 Series Ignition with its white wire or points terminal, you will need the PN 8910 Tach Adapter. The PN 8910 will correct the operation of most voltage-triggered tachometers or fuel injection systems that do not work directly off the tach output terminal of the MSD Ignition Unit.
MSD Performance Ignition - 86-93 Mustang GT Ford TFI Coil, Hi Performance
Top off your Ford or GM Ignition system with these great new replacement coils. The Blaster TFI and GM Coils have MSD performance in factory style housings!MSD designed these Coils by combining our Blaster Coil experience with E-core coil efficiency. Each coil has a unique turns ratio plus there is lower primary resistance than the stock coil. This all amounts to a bolt-in replacement coil that produces more output voltage. The Coils will work with stock ignition systems as well as MSD equipped cars and trucks. Installation Tip: If you plan to install an MSD Ignition with your Blaster TFI Coil, use a PN 8874 Harness for a direct plug-in installation.
MSD Performance Ignition - 86-93 Mustang GT Red Super Conductor Ford 302, 351W, HEI
The MSD 8.5mm Super Conductor Wire is "the" performance wire.Engineered from the inside out, the 8.5 offers everything you have everwanted in a wire; incredibly low resistance without electronic interference! In a single 12 inch length of Super Conductor Wire there is only 40 - 50 ohms of resistance!
PMAS - 86-04 Mustang GT & Cobra 05+ Style MAF Conversion Kit for 86-04 with HPX
In 2005 Ford Introduced a new style of mass-air sensor. It is commonly referred to "slot" or "card" style. This sensor has no housing, the stock airbox has a receptable for the sensor
PMAS - 89-11 Mustang GT & Cobra HPX 05+ Slot Style MAF Sensor
The HPX MAF sensor will support 600+RWHP in a 3" tube. It is recomended for high horsepower blow through applications. This is an 05+ Ford slot style MAF. This is a direct bolt in for 05+ Fords, older cars will require a flange and pigtail (sold seperately on this website). Pigtails and adapter harnesses can be found here. Flanges for mounting this sensor directly into a tube can be found here. Entire housings for this MAF sensor can be found here.
In larger housings this MAF sensor will support even more power. If more range is needed, an extender type device can be used.
Tube Size Est. HP range with HPX sensor
3" 300-750RWHP
3.5" 750-900RWHP
4" 1000+RWHP
4.5" 1000+RWHP
SCT Performance Tuners - 07-11 Mustang Shelby GT500 & 87-10 GT SCT 6600 Multi-Position Chip
Looking for a low cost tuning solution for your 87-04 vehicle? The 6600 Multi-position chip comes with 2 custom tunes and can hold up to 4! Included is the 6600 chip, cable, and switch to alternate between programs. With a custom tuned 6600 Chip you will recieve the following benifits:
•Increased horsepower and torque. Click Here for dyno-proven results for all vehicles.
•Speedometer correction for different rear end gears and/or tires (99+ vehicles only).
•Speed Limiter Removal.
•Rev Limiter adjustment (we safely raise rev limiter several hundred RPM's).
•Improved throttle response (greatly improved on 05+ Electronic Throttle Control Cars).
•Firmer Faster shifting with Automatic Transmission vehicles.
•Disabled Traction Control (if desired, 98+ vehicles only).
•Lowered cooling fan on / off temperatures (allows engine to run cooler & prevent sluggishness in hot weather).
•Improved Gas Mileage.
SCT Performance Tuners - 79-11 Mustangs & All Ford Trucks VMP Custom E-Mail Tune for X2,X3,Livewire,TSX Tuners
Email Custom Tune file pricing for NA vehicles that are stock or have basic bolt ons: 1 file for $59, 2 for $99, or 3 for $129
Spohn Magnetic Angle Finder
Magnetic angle finder tool used to accurately set your pinion angle.
Strange Engineering 1987-1993 Mustang 8 cylinder - 4-1/2"' lug pattern
Strange lightweight bolt-on disc brake kits feature cutting edge technologythat's available in easy to install bolt-on kits for your car. Each kit included specifically engineered and matched components with premium grade hardware for installation on the specified spindles or rear axle applications. Features include direction billet multi-piston calipers, one-piece forged steel slotted rotors, and lightweight billet aluminum hubs.
VMP Tuning - 86-04 Mustang GT & Cobra 05+ Style MAF Conversion Kit for 86-04 with MAFIA
In 2005 Ford Introduced a new style of mass-air sensor. It is commonly referred to "slot" or "card" style. This sensor has no housing, the stock airbox has a receptable for the sensor.
VMP Tuning - 89-04 Mustang GT & Cobra VMP Blow-through 75MM MAF housing and HPX MAF sensor
The ultimate MAF for blow-through applications! Great for Procharger, Vortech, Powerdyne, and custom Turbo Kits. Works great on any year MAF based vehicle from Fox bodies to 2008s. The HPX sensor gives enough range for most applications making 650RWHP or less.
VMP Tuning - 89-11 Mustang GT & Cobra VMP Blow-through 75MM MAF housing and OEM 05+ MAF sensor
Part Number: 05OEM75MM is a package which includes VMP housing and OEM Ford 05+ Slot style sensor, good for 150-300RWHP, use extender for more range. See option details below.
VMP Tuning - 89-11 Mustang GT & Cobra VMP Blow-through 75MM MAF housing and SCT BA5000 MAF sensor
Part Number: BA75MM is a package which includes VMP housing and the new SCT BA5000 Slot Style Sensor, good for 250-650RWHP, use extender for more range. See option details below.
The ultimate MAF for blow-through applications! Great for Procharger, Vortech, Powerdyne, and custom Turbo Kits. Works great on any year MAF based vehicle from Fox bodies to 2008s. This sensor in a 75MM housing gives enough range for most applications making 650RWHP or less.
Window Net
Protect yourself in style.
24 in. x 24 in. ribbon window net
Required by most sanctioning bodies, this 24 in. x 24 in. window safety net is SFI 27.1 approved and mounts to the roll cage in your car with the optional installation kit. Made from durable nylon ribbon in your color choice, this net keeps you from being thrown from your car or from debris entering in the event of an accident, and adds some style as well.
Select your color choice.
Window Net Mounting Kit
Installation of a window net made easy.
Window Net Installation Kit - This universal installation kit will fit most square nets and includes rod kit, with GM seatbelt style fastener.
