Ford Racing Performance Parts 2005-2010 MUSTANG GT - Shorty Headers
Also fits early “Fox” vehicles with modifications
2 Jet-Hot® Limited Warranty
3 Production and all GT-40 heads
5 Finally a header that fits the new angled spark plug 5.0L GT-40 “P” cylinder head. Fits 1986-93 Mustangs with stock or aftermarket H-pipe. Also fits 1979-85 Mustangs and other Fox chassis with minor modification
Ford Racing Performance Parts 2005-2010 MUSTANG GT 4.6L - 3V COLD AIR TUNER KIT
Fits 2005-2009 Mustang GT with Manual or Automatic transmission
Designed for those that want the Ford Racing Cold Air Intake for aftermarket performance tuning/calibration.
Kit comes with hardware only! Calibration not included! Kit intended for aftermarket calibrators.
Ford Racing Performance Products - 2005-2010 Mustang GT - Ford Racing 85mm Cold Air Kit
More Power. Replace your restrictive stock intake with a Ford Racing CAI for more power and better acceleration. The Ford Racing GT Cold Air Intake Kit with its 85mm mass air meter and custom tune will increase your GT Mustangs power by up to 20 rwhp.
J&M Motorsports - 07-11 Mustang Shelby GT500 & 05-10 GT J&M Motorsports Billet LCA
2005-Pres. Mustang Street Aluminum Billet Lower Control Arms
J&M Motorsports - 07-11 Mustang Shelby GT500 & 05-10 GT J&M Motorsports Double Adjustable Upper Control Arm Street
Just like the lower control arm bushings in the Mustang the upper control arm can have a significant impact on the vehicle’s ride, comfort, handling, acceleration, noise and vibration. When the car leans (i.e., rolls) in a turn, one side of the chassis moves upward relative to the rear axle, the other side moves downward, and the upper control arm must twist (rotate) to allow for the axle to articulate through its suspension travel. This rotation causes the control arm bushing to bind. If this bind becomes excessive, it will raise the rear wheel rate and produce sudden, uncontrolled, undesirable changes in handling (e.g., snap oversteer).
J&M Motorsports - 07-11 Mustang Shelby GT500 & 05-10 GT J&M Motorsports Ultimate LCA
J&M street/race Lower control arms in flat black powdercoat.
Don't let the race part scare you, we installed them in our 2011 5.0L Mustang and could not tell they were there, except from the lack of wheel hop when launching hard at the track.
JLT Performance - 2005-2010 Mustang GT - JLT Performance Cold Air Intake
The new 2005-2010 GT has a totally new drive by wire computer system and reacts to modifications much different then the previous models. Why use the same old style of intake from previous years? Instead, use the intake that won the 5.0 Mustang Cold Air Intake Shootout! Why did it do so well in the shootout? Simple. This JLT intake was developed in conjunction with SCT, the leaders of S197 Mustang GT tuning.
K&N Air Filters 2005-2010 Mustang Gt - FIPK Air Intake Kit
Improves Horsepower. The K&N "Fuel Injection Performance Kit" (FIPK for short) Air Intake kit completely replaces your stock 2005-2010 GT Mustangs restrictive stock factory air box and paper filter with a high flow K&N filter assembly and intake tube for a noticeable increase in horsepower and acceleration while still providing excellent filtration.
K&N Air Filters and Intakes - 2010 MUSTANG GT HIGH-FLOW K&N / FORD RACING AIR FILTER
* K&N 4 ply panel washable air filter
* Fits stock 2010 Mustang GT airbox. Will NOT fit 2005-2009.
* Flows approximately 22% more than stock filter at 1.5" H2O delta pressure
* Co-Engineered by K&N and Ford Racing
* Does not require PCM recalibration
LPW - 05-11 Mustang GT & Cobra LPW Ford 8.8" rear end cover - Ultra Low Profile
LPW Ultra-Low profile Rear end cover/girlde for the Ford 8.8" rear ends.
Fits 05+ Mustangs, NO panhard relocation required.
Strengthens rear end, improves cooling, and increases fluid capacity. Includes drain and fill holes.
LPW PN 201-8.8
Magnaflow Exhaust 2005-2010 FORD MUSTANG GT Stainless Cat-Back System PERFORMANCE EXHAUST
Features and Benefits: Lifetime Warranty, Dyno Tested And Proven To Make Power, Performance Gains In Horsepower And Torque, Great Sound -Has A Smooth; Deep Tone, Easy To Install, Mandrel-Bent. All Welded. Built To Last.
Magnaflow Exhaust 2005-2010 FORD MUSTANG GT - Stainless Cat-Back System PERFORMANCE EXHAUST
Features and Benefits: Lifetime Warranty, Dyno Tested And Proven To Make Power, Performance Gains In Horsepower And Torque, Great Sound -Has A Smooth; Deep Tone, Easy To Install, Mandrel-Bent. All Welded. Built To Last.
METCO 1979-2010 Mustang & Ford Truck - Fuel Rail Adapter
METCO Ford Fuel Rail Adapter
This exclusive adapter is only available from Metco Motorsports!
This adapter fitting is CNC-machined from stainless steel and attaches directly to the schrader valve outlet on the Ford factory fuel rail. The front side of the fitting accepts a standard 1/8" NPT fitting for a direct-mount fuel gauge or a gauge sending unit.
METCO 1979-2010 Mustang & Ford Truck - Rail Mount Fuel Gauge
METCO Ford Rail Mount Fuel Gauge
Ford Fuel Rail Gauge Kit
5.0 Mustang, 4.6 Cobra, Lightning
This exclusive kit is only available from Metco Motorsports!
This kit is based on our exclusive adapter fitting that is CNC-machined from stainless steel. The adapter attaches directly to the schrader valve outlet on the Ford factory fuel rail, and the opposite side of the fitting accepts the standard 1/8" NPT fitting for the included 1.5" fuel pressure gauge.
METCO Ford 2002 & Newer Modular V8 (with Twin Helix Mount)
This valve cover breather assembly replaces the original oil fill tube found on the factory passenger side valve cover. The base is CNC-machined from billet aluminum for precise fit, and the included silicone gasket is specially designed to prevent oil seepage at the base of the breather. The filter base is microfinished for surface protection and good looks, and is easily hand-polished to a mirror-like appearance. The removable filter element is a high-quality reusable unit from S & B Filters, and it is securely retained in the filter base by a specially machined retention groove at the top of the base.
